Wattflyer RC Network: RC Universe :: RCU Magazine :: RCU Forums :: RCU Classifieds :: RCU User Reviews :: RCU YouTube
Home Who's Online Calendar Today's Posts RealTime Post Spy Mark Forums Read
Go Back   WattFlyer RC Electric Flight Forums - Discuss radio control eflight > Search Forums
Register Members List Wattflyer Extras Articles Search Today's Posts Mark Forums Read Social Groups

Thank you for your support (hide ads)

Showing results 1 to 15 of 15
Search took 0.01 seconds.
Search: Posts Made By: stemo99
Forum: Beginners 11-19-2013, 07:01 PM
Replies: 13
Views: 885
Posted By stemo99
21 minutes on a 400 class motor with a 2200mah...

21 minutes on a 400 class motor with a 2200mah battery, yeah right.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros 11-11-2013, 01:27 AM
Replies: 3
Views: 468
Posted By stemo99
Thanks Turner and Hillbillie, it works!!!!! I...

Thanks Turner and Hillbillie, it works!!!!! I now have it set up as follows in the flap system screen: The 3 position flap switch controls the gyro.

NORM. UP 100%
MID. DOWN 100%
LAND. ...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros 11-10-2013, 09:41 PM
Replies: 3
Views: 468
Posted By stemo99
HK RX3S Receiver/Gyro on off problem with DX7

I have a HK RX3S version 3 receiver/gyro that can be turned on and off via the radio. I have an older DX7 radio and have all gyro and contol surfaces working properly except controling the on off...
Forum: General Electric Discussions 09-01-2013, 01:47 PM
Replies: 18
Views: 1,609
Posted By stemo99
Chainsaw, works every time. After 6 months of...

Chainsaw, works every time. After 6 months of trying everything else unsucessfully, I finally got her down. Plane was trashed but all the electronics minus the battery worked fine.
Forum: General Electric Discussions 08-18-2013, 10:38 PM
Replies: 44
Views: 1,591
Posted By stemo99
Wink Chellie, didn't imply that a 50 or 60 was the...

Chellie, didn't imply that a 50 or 60 was the wrong motor to use, just asked if the op read the reviews that stated the motors being used by people who actually own and fly them. One review stated...
Forum: General Electric Discussions 08-18-2013, 01:22 AM
Replies: 44
Views: 1,591
Posted By stemo99
If you read the reviews on the Nitro page, no one...

If you read the reviews on the Nitro page, no one is using anything near as large as a 50 or 60 motor. Most are using a 25 to 32 size motor. I have a Sig Seniorita with a headsup 32, 60 amp...
Forum: Scratch and Kit Built Aircraft 06-10-2013, 01:23 PM
Replies: 30
Views: 1,794
Posted By stemo99
Flys so well a monkey can do it!

Flys so well a monkey can do it!
Forum: General Electric Discussions 06-02-2013, 08:39 PM
Replies: 1,984
Views: 122,704
Posted By stemo99
thanks

thanks
Forum: General Electric Discussions 05-31-2013, 01:36 AM
Replies: 17
Views: 1,379
Posted By stemo99
It may be your allen wrench is worn. If you have...

It may be your allen wrench is worn. If you have a grinder or even a Dremel, grind off the end till it's flat and has 6 sharp new points on the end. It has worked for me many times.
Forum: General Electric Discussions 05-13-2013, 12:51 PM
Replies: 1,984
Views: 122,704
Posted By stemo99
Just finished and maidened my Sig Four Star 20ep...

Just finished and maidened my Sig Four Star 20ep and man she sure flys nice.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros 03-01-2013, 12:43 PM
Replies: 10
Views: 2,035
Posted By stemo99
On the other group, I was advised that if the...

On the other group, I was advised that if the Mix1 is used on a DX7 that the left aileron trim will not work. I tried the trim and that IS the case. Mix5 or Mix6 MUST be used and left aileron trim...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros 02-28-2013, 11:45 AM
Replies: 10
Views: 2,035
Posted By stemo99
Did all of the suggested above and yay!!!, it all...

Did all of the suggested above and yay!!!, it all works. I have adjusted the throws for flaps and elevator on the 3 position switch to pos 0 normal, pos1 1/2 flap deflection, pos2 full flaps. Thank...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros 02-26-2013, 08:48 PM
Replies: 10
Views: 2,035
Posted By stemo99
I have the left aileron plugged into channel 6...

I have the left aileron plugged into channel 6 which is aux1 (now I know it'sthe flap channel) and ailerons work fine. I'll try your suggestion and post results. Thanks for your input.
Steve
Forum: RC Radios, Transmitters, Receivers, Servos, gyros 02-24-2013, 06:17 PM
Replies: 10
Views: 2,035
Posted By stemo99
DX7 Flap Programming for 3 position switch

First, the radio is a DX7 NOT a DX7s. OK I want to use my 3 position flap switch for no flaps, half flaps and full flaps. The wing has 2 aileron servos and 1 flap servo. I am using a 7 channel...
Forum: General Electric Discussions 01-01-2012, 08:03 PM
Replies: 36
Views: 3,281
Posted By stemo99
Did you balance this prop B4 reving it up? An...

Did you balance this prop B4 reving it up? An out of balance condition could attribute to this happening.
Showing results 1 to 15 of 15

 
Forum Jump

All times are GMT +1. The time now is 07:00 PM.


Powered by: vBulletin
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright 2005 WattfFlyer.com
RCU Eflight HQ

Charities we support Select: Yorkie Rescue  ::  Crohn's & Colitis Foundation



Page generated in 0.11459 seconds with 13 queries