Home Who's Online Calendar Today's Posts RealTime Post Spy Mark Forums Read
Go Back   WattFlyer RC Electric Flight Forums - Discuss radio control eflight > Electric Airplanes > Foamies
Register Members List Wattflyer Extras Articles Search Today's Posts Mark Forums Read Social Groups

Foamies Talk about building, power setups and anything having to do with e-powered foamy planes!

Thank you for your support (hide ads)
Reply
 
Thread Tools Display Modes
Old 11-05-2009, 12:51 AM   #26
kc135boomer
NKAWTG...N!!!
 
Join Date: Aug 2005
Location: Altus AFB, Ok
Posts: 59
Thanked 1 Time in 1 Post
iTrader: (0)
Friends: (1)
Default

Sweet! Thanks for the quick reply.
kc135boomer is offline  
  Reply With Quote
Old 11-07-2009, 06:24 PM   #27
kc135boomer
NKAWTG...N!!!
 
Join Date: Aug 2005
Location: Altus AFB, Ok
Posts: 59
Thanked 1 Time in 1 Post
iTrader: (0)
Friends: (1)
Default

Well it flew. I was a little worried as it seem to take forever to get up to speed but it finally got so S1 and leaped off the ground and went straight up (kind of looked like Fat Albert!)

I nosed it over and checked the rates which seemed to be dead on.

About 3 minutes into the flight the #4 prop flew off (kind of like the MC rate of the real ones) and into nowhere land. I made the circle to land, kept a ton or rudder into it and brought it down to a nice landing. I searched high and low for the prop but at this point I think is is gone. Hopefully I can order a new one (including the adapter) and fly it again. I think I am going t remove all four and epoxy them on to the motors as the GWS way sucks! Over all, this is going to be a fun little airplane and boy does it fly scale!!
kc135boomer is offline  
  Reply With Quote
Old 11-07-2009, 10:27 PM   #28
kc135boomer
NKAWTG...N!!!
 
Join Date: Aug 2005
Location: Altus AFB, Ok
Posts: 59
Thanked 1 Time in 1 Post
iTrader: (0)
Friends: (1)
Default

Update: I went back out to look for the prop. After 2 hours of nothing I decided to head out when I looked down and there it was! Except for the spinner I am good to go. My thought is to JB weld the adapters on the shaft so it does not happen again. Thoughts on this idea?
kc135boomer is offline  
  Reply With Quote
Old 11-08-2009, 01:05 AM   #29
Nitro Blast
Community Moderator
 
Nitro Blast's Avatar
 
Join Date: Aug 2005
Location: Sunny San Diego Ca
Posts: 1,898
View Nitro Blast's Gallery33
Thanked 220 Times in 177 Posts
Club: Silent Electric Fliers of San Diego & Miramar RC Flyers of San Diego
Send a message via MSN to Nitro Blast
Awards Showcase

Globetrotter Pilot  AP Contest Winner  3kW 
iTrader: (15)
Friends: (35)
Default

Top knotch! It was never lost, just misplaced!

Electricity... It's not just for light bulbs anymore.

Project Globetrotter Participant 7/09
Wings Across America Participant
AirfoilZ Factory Field Rep
BMK Designs BMK Designs
Nitro Blast is offline  
  Reply With Quote
Old 11-08-2009, 05:18 PM   #30
kc135boomer
NKAWTG...N!!!
 
Join Date: Aug 2005
Location: Altus AFB, Ok
Posts: 59
Thanked 1 Time in 1 Post
iTrader: (0)
Friends: (1)
Default

Take 2 today, I jb welded all the prop shafts on and went out again. The wind was kind of strong at 13 kts but it was right down the pipe. I balanced it exactly per the instructions and am still dumbfounded that the nose wheel barely touches the ground but I put it in the wind, gave it full power and in less than 10 feet it was airborne. It only needed a bit of down trip and flew real well. I am impressed how scale it actually looks. I flew for 15 minutes and did two bounce and goes. On the third attempt the wind caught it and I went around. Most airplanes would have stalled at the push it up point but this bird just flew away. Thanks to all that have given me advise on setup and such. I have a new favorite under $50 plane!
kc135boomer is offline  
  Reply With Quote
Old 11-10-2009, 10:42 PM   #31
kc135boomer
NKAWTG...N!!!
 
Join Date: Aug 2005
Location: Altus AFB, Ok
Posts: 59
Thanked 1 Time in 1 Post
iTrader: (0)
Friends: (1)
Default

I got to fly it last night with zero wind and I recommend this plane to anyone that wants a lazy flyer that is cool to look at and sounds awesome. On a 2S 1300 lipo I got 15 minutes of sustain flying to include about 10 touch and go's. The plane is slow just like the real one and stops traffic in its traps..





Can you find it?
kc135boomer is offline  
  Reply With Quote
Reply

  WattFlyer RC Electric Flight Forums - Discuss radio control eflight > Electric Airplanes > Foamies

« Previous Thread | Next Thread »

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Video - HBK2 Maiden Flight racin06 Micro Sized Electric Helicopters 1 03-01-2008 02:31 AM
My Maiden of my Belt CP Chopper!! VIDEO** jaskel Beginners - Helis 19 02-15-2008 09:50 PM
GWS CargoTrans C-130 Hercules Blue Angels Fat Albert Decals RCJacq General Electric Discussions 0 10-04-2006 03:03 PM
Video of my Flying Styro F-16 maiden. tahustvedt Electric Ducted Fan Jets 8 09-20-2006 04:37 AM
Video of my easystar maiden flight luisfc1972 Beginners 10 03-26-2006 05:41 PM


All times are GMT +1. The time now is 07:46 AM.


Powered by: vBulletin
Copyright ©2000 - 2009, Jelsoft Enterprises Ltd.
Copyright 2005 WattfFlyer.com
RCU Eflight HQ

Select charities we support: Yorkie Rescue  ::  Crohn's & Colitis Foundation

Page generated in 0.23048 seconds with 33 queries