|Wattflyer RC Network: RC Universe :: RCU Magazine :: RCU Forums :: RCU Classifieds :: RCU User Reviews :: RCU YouTube|
|Register||Members List||Wattflyer Extras||Articles||Search||Today's Posts||Mark Forums Read||Social Groups||Photo Gallery|
|Power Systems Talk about motors, ESC speed controllers, gear drives, propellers, power system simulators and all power system related topics|
|Thank you for your support (hide ads)|
||Thread Tools||Display Modes|
|01-21-2014, 12:54 AM||#1|
Behold The Renaissance
Join Date: May 2012
Location: So. Calif
Thanked 103 Times in 101 Posts
Club: AMA, Marks, Pomona Valley, Prado Dam
Brushed Power System Throttle Reverse
Any thoughts are welcome.......(well almost any)......lol
The TX/RX is an older 2.4ghz (4ch/TX - 6ch/RX)....FMS/ArtTech/BlitZWorks.
The motor is the standard GWS Slow Stick (geared) brushed.
The ESC is a Turnigy Eagle 30amp.
The battery is a 2s, 7.4v, 1600mah.
Everything was in good working order the last time I powered everything up (on a Slow Stick)....been about 8 months ago. Batteries are fine, use them occasionally on the Tiger Moth.
Got back from flying this morning and a buddy was bugging me to bring out the SS again so we can play tag.....lol
So, I dusted everything off and put everything back together.......did a bench test on controls and the motor would not turn over.....no beeps on the ESC and control surface's worked fine.
Powered down everything, check'd reverse tabs.....all ok for this application.....power'd it up again, no ESC beeps, throttle stick down, but motor now running full throttle......Powered down, reversed ch2 (throttle), powered up....same thing, motor running full throttle.....throttle down by pushing stick UP.....lol
Tried three re-binds with throttle stick in 3 different positions......no change and ESC beeps as if it senses the throttle stick NOT in lowest postion (down)....no other beeps and motor turns in proper direction when running (checked it with a prop attached to make sure).
Tried one more boot-up....with throttle stick down, all tabs correctly set and no prop.....same story, ESC has that slow beep...beep....beep like stick not in proper position...and motor blazing (it will stop and slow down as the stick is shoved upward).
Never had this happen before with any application I've built with the brushed slow stick (reversed motor once due to wire crossing)......and yes, I've checked red to red....black to black and plug input to RX....all are as I have done previously...100 times....lol
Really don't want to put the Stick on the DX6i and waste a good RX and selection slot.....but may have to if the cheepy TX/RX has given up the ghost.....it's been pretty good to me for the Stick up until now.....lol
Thanks in advance........
|Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)|
|Thread||Thread Starter||Forum||Replies||Last Post|
|Everything You Wanted To Know About Electric Powered Flight||AEAJR||Beginners||155||01-24-2015 05:28 PM|
|Everything You Wanted To Know About Electric Powered Flight||AEAJR||General Electric Discussions||269||06-27-2014 01:06 PM|
|help with power system for 25% Cub||neddy191||Power Systems||11||04-11-2013 03:24 AM|
|convert brushed power sys to brushless?||GaryJ||Power Systems||12||04-09-2013 10:43 PM|
|ELERC Micro A-10 Warthog 30mm EDF Beta Test||Joe 1320||Electric Ducted Fan Jets||13||02-02-2012 01:15 PM|