Wattflyer RC Network: RC Universe :: RCU Magazine :: RCU Forums :: RCU Classifieds :: RCU User Reviews :: RCU YouTube
Home Who's Online Calendar Today's Posts RealTime Post Spy Mark Forums Read
Go Back   WattFlyer RC Electric Flight Forums - Discuss radio control eflight > Electric R/C Airplanes > Delta & Flying Wings
Register Members List Wattflyer Extras Articles Search Today's Posts Mark Forums Read Social Groups

Delta & Flying Wings Discuss electric powered delta (flying wing) style aircraft here.

Thank you for your support (hide ads)
Reply
 
Thread Tools Display Modes
Old 07-04-2014, 07:10 AM   #1
mclarkson
Super Contributor
 
mclarkson's Avatar
 
Join Date: May 2010
Location: Wichita, KS
Posts: 2,803
View mclarkson's Gallery4
Thanked 170 Times in 168 Posts
Awards Showcase

Scratchbuilders Award  Outstanding Contributor Award 
iTrader: (0)
Friends: (7)
Default UMX Frankendelta

It all started with my JAS-39 Gripon (retired).



After a serious nose-in, it's nothing more than a twisted hulk of foam that I trip over occasionally. But I noticed the wings were still in pretty good shape. What if, I wondered, I pried them off and stuck them together? Could I stick a motor in the back and make a tiny flying wing?



I actually thought it looked super-cool. I chopped the elevons up to make room for a propeller. Then chopped them up some more. Then decided that this should really be a tractor delta, rather than a pusher wing, so I had to glue them all back together again.

The wings didn't quite fit together, as they have some raised 'tabs' that originally fit into holes in the fuselage. I decided to retain the space in the middle to mount my equipment in. I a bamboo skewer through each set of tabs to hold everything in alignment and create some internal spars.

I made a firewall out of some plywood and stuck it in the front, then mounted a Turnigy 2730-3000 outrunner (from a destroyed Adrenaline Rush) to it. I didn't want the servos dragging on the ground, and the 6 gram servos I'm using didn't fit the original pockets anyway, so I cut new holes in the wing and mounted the servos vertically in them.


Here's a top view where you can see the round 'tabs,' and the empty center space they create, pretty well.


I used blue fanfold foam to fill the gap in the bottom of the wing. You can see the little 6gram servos sitting in their giant, empty pockets as well.


This gets covered up with tape, along with the empty servo sockets.


The receiver sits up front


And the Turnigy Plush 10A ESC sits all the way at the back. This is mainly due to the length and amount of wires to be fit into the middle.


I made winglets for the rear of the wing. They are modeled on the original Gripon's canards, but made of blue fanfold foam.


I ran two strips of "Velcro" down the gap on the top, to temporarily mount my battery while I try to work out the best CG for the plane.


With a 17" wingspan, it weighs 4.4 ounces without a battery. AUW with an 850mAh 2-cell is 6.2 ounces. With a 5x3 prop, it develops 12.2 ounces of thrust and goes in the neighborhood of 50MPH. It will roll at a ridonculous 200 RPM.


mclarkson is offline  
  Reply With Quote
Old 07-04-2014, 07:14 AM   #2
mclarkson
Super Contributor
 
mclarkson's Avatar
 
Join Date: May 2010
Location: Wichita, KS
Posts: 2,803
View mclarkson's Gallery4
Thanked 170 Times in 168 Posts
Awards Showcase

Scratchbuilders Award  Outstanding Contributor Award 
iTrader: (0)
Friends: (7)
Default

Once I get the CG ironed out, I'll be building something a little more permanent for the battery.

mclarkson is offline  
  Reply With Quote
Old 07-04-2014, 12:15 PM   #3
Porcia83
Member
 
Join Date: Feb 2010
Posts: 157
Thanked 8 Times in 8 Posts
iTrader: (3)
Friends: (1)
Default

love it! I did something with a beater T-28 I had. Shaved the canopy off and made it a pylon racer, then later went with landing gear on top so I could land inverted, then eventually made it a bipe...that was the final nail in the coffin.

Looking forward to updates.
Porcia83 is offline  
  Reply With Quote
Old 07-05-2014, 01:29 PM   #4
soarrich
Soarrich
 
soarrich's Avatar
 
Join Date: May 2012
Location: NJ, USA
Posts: 147
Thanked 8 Times in 7 Posts
Club: JCSF & MMAC
iTrader: (0)
Friends: (0)
Default

That looks pretty cool. I have a J-39 that I've flown a couple of times, it's a bit of a handful. I'm hoping I can get it to fly better, but this looks like a good use if I can't.
soarrich is offline  
  Reply With Quote
Reply

  WattFlyer RC Electric Flight Forums - Discuss radio control eflight > Electric R/C Airplanes > Delta & Flying Wings

« Previous Thread | Next Thread »

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
UMX SBach 342 thepiper92 Indoor & Micro Electric Planes 11 07-08-2014 03:43 AM
UMX Carbon Cub 2s 180 motor with flaps, lights and even floats!! rcers Indoor & Micro Electric Planes 18 12-23-2013 05:02 AM
Gee BEE UMX ASX3 - Need Help JR2012 Indoor & Micro Electric Planes 2 11-30-2012 05:19 PM
UMX Beast -reinforcing the stabilizer and the elevator rags Indoor & Micro Electric Planes 2 11-30-2012 05:18 AM
E-Flite Sbach 342 UMX battery DCDetector General Electric Discussions 3 11-28-2012 01:39 AM


All times are GMT +1. The time now is 10:11 AM.


Powered by: vBulletin
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright 2005 WattfFlyer.com
RCU Eflight HQ

Charities we support Select: Yorkie Rescue  ::  Crohn's & Colitis Foundation



Page generated in 0.15169 seconds with 27 queries