Wattflyer RC Network: RC Universe :: RCU Magazine :: RCU Forums :: RCU Classifieds :: RCU User Reviews :: RCU YouTube
Home Who's Online Calendar Today's Posts RealTime Post Spy Mark Forums Read
Go Back   WattFlyer RC Electric Flight Forums - Discuss radio control eflight > Electric R/C Airplanes > Foamies
Register Members List Wattflyer Extras Articles Search Today's Posts Mark Forums Read Social Groups

Foamies Talk about building, power setups and anything having to do with e-powered foamy planes!

Thank you for your support (hide ads)
Reply
 
Thread Tools Display Modes
Old 03-13-2007, 01:32 PM   #1
nk1851
Member
 
Join Date: Jan 2007
Posts: 57
Thanked 0 Times in 0 Posts
iTrader: (0)
Friends: (0)
Default Foam safe CA - are there secrets?

Purchased my first foamy (Great Planes Yak 55 3D ARF ) and started to put it together. Not having experience with foam safe CA, I went to the LHS and purchased ZAP-O foam safe CA. Asked the proprietor if I needed kicker and was told that it was not really needed, that foam safe acted just like regular CA, and the kicker just accelerated the cure.
When I got home, began assembly, first step being to CA the wing halves together. I applied the CA, held the wing halves together for a few minutes and tried to lay them down and they fell apart. The glue didn't work!. I tried again with the same results. I even let it cure over night and the bond was very minimal.
Questions:
1. Will foam safe go bad sitting on the LHS shelf - did I just get a bad bottle?
2. Are there special steps to accomplish when using this stuff?
3. Do you really need the kicker to make it work?
4. Anybody got any ideas on where I screwing up, and can make this stuff work?
Thanks,
Nick
nk1851 is offline  
  Reply With Quote
Old 03-13-2007, 02:01 PM   #2
reg3
Member
 
reg3's Avatar
 
Join Date: Jun 2006
Location: Florence, AL
Posts: 72
Thanked 5 Times in 5 Posts
iTrader: (1)
Friends: (1)
Default

Originally Posted by nk1851 View Post
3. Do you really need the kicker to make it work?
4. Anybody got any ideas on where I screwing up, and can make this stuff work?
Yes, you really need some kicker. I have used baking soda before to make it "kick". Good luck.
reg3 is offline  
  Reply With Quote
Old 03-13-2007, 02:08 PM   #3
gsk11740
I'm outta here!
 
Join Date: Oct 2006
Posts: 1,195
Thanked 2 Times in 2 Posts
iTrader: (1)
Friends: (0)
Default

I tried to put together a Great Planes FlatOuts J-3 with the same results. I had several people tell me forget the CA and use a hot glue gun.
gsk11740 is offline  
  Reply With Quote
Old 03-13-2007, 02:15 PM   #4
firemanbill
Community Moderator
 
firemanbill's Avatar
 
Join Date: Sep 2005
Location: Yorktown, Virginia USA
Posts: 18,860
View firemanbill's Gallery67
Thanked 718 Times in 706 Posts
Club: Newport News Park R/C Club
Awards Showcase

125mph Speed Demon  100mph Speed Demon  2kW  4kW 
iTrader: (35)
Friends: (63)
Default

The ca uses moisture to set. that is why your fingers will instantly bond when you get some on them. Stryo is by nature very very dry so kicker is a must!

I don't use it for joints that require strength. Use a contact cement safe for foam or epoxy for that. Areas like the fuse halves, wing joins and such.

CA is ok for small repairs and attaching detail accessories and such. I have never had good result trying to use ca as the main bonding agent.

2012 SEFF Night Bowling Champion!
firemanbill is offline  
  Reply With Quote
Old 03-13-2007, 02:31 PM   #5
Grasshopper
Some Assembly Required
 
Grasshopper's Avatar
 
Join Date: Feb 2006
Location: Nashville, TN
Posts: 12,071
View Grasshopper's Gallery48
Thanked 422 Times in 407 Posts
Awards Showcase

AP Contest Winner  WAA-08 Pilot  100mph Speed Demon 
iTrader: (49)
Friends: (52)
Default

Originally Posted by gsk11740 View Post
I tried to put together a Great Planes FlatOuts J-3 with the same results. I had several people tell me forget the CA and use a hot glue gun.
Be careful when using hot glue on foam. Some of the higher temp glues will melt the foam. I only use low melt. As Bill said, I would use epoxy or Gorilla glue for joints that require a lot of strength. I rarely use CA on foam.

Tom
Grasshopper is offline  
  Reply With Quote
Old 03-13-2007, 05:27 PM   #6
crxmanpat
Community Moderator
 
crxmanpat's Avatar
 
Join Date: Feb 2006
Location: Mesa, AZ
Posts: 6,265
Thanked 319 Times in 308 Posts
Club: Arizona Model Aviators
Awards Showcase

WAA-08 Pilot  100mph Speed Demon  Globetrotter Pilot 
iTrader: (2)
Friends: (27)
Default

I'm with Bill. Use some type of contact cement for making strong foam joints like wing and fuse halves. On all of my GWS birds, I use the cement they supply. It works perfectly if used correctly. Apply a thin layer of cement on each half and let stand for 5-10 minutes until it gets tacky. Then simply press the halves together and tape. Caution, you typically only get one shot at lining things up straight. I usually let this stuff cure overnight, although it should be good after a few hours.

An alternate method is to apply a layer of cement to one part, press the parts together briefly and pull apart, and let it set for 5-10 minutes. Then press together and tape.

There are also other glues thay can be used such as Gorilla Glue or Elmers Ultimate Glue (basically the same stuff), UHU Por or UHU Creativ, or any other type of contact cement.

Pat Gagnon

Owner - Nico Hobbies

Your source for micro pusher jets!
crxmanpat is offline  
  Reply With Quote
Old 03-13-2007, 05:56 PM   #7
gsk11740
I'm outta here!
 
Join Date: Oct 2006
Posts: 1,195
Thanked 2 Times in 2 Posts
iTrader: (1)
Friends: (0)
Default

Originally Posted by Grasshopper View Post
Be careful when using hot glue on foam. Some of the higher temp glues will melt the foam. I only use low melt. As Bill said, I would use epoxy or Gorilla glue for joints that require a lot of strength. I rarely use CA on foam.
...as Gary roots around looking for the receipt to see if the glue gun and sticks he ordered are the low temp melt variety...

Good! Got the right one!
gsk11740 is offline  
  Reply With Quote
Old 03-13-2007, 06:31 PM   #8
firemanbill
Community Moderator
 
firemanbill's Avatar
 
Join Date: Sep 2005
Location: Yorktown, Virginia USA
Posts: 18,860
View firemanbill's Gallery67
Thanked 718 Times in 706 Posts
Club: Newport News Park R/C Club
Awards Showcase

125mph Speed Demon  100mph Speed Demon  2kW  4kW 
iTrader: (35)
Friends: (63)
Default

Just be carefule using hot glue if you ever leave it in a hot car the glue may melt since it has a low melting point. Hence the name I guess.

2012 SEFF Night Bowling Champion!
firemanbill is offline  
  Reply With Quote
Old 03-13-2007, 06:33 PM   #9
gsk11740
I'm outta here!
 
Join Date: Oct 2006
Posts: 1,195
Thanked 2 Times in 2 Posts
iTrader: (1)
Friends: (0)
Default

Originally Posted by firemanbill View Post
Just be carefule using hot glue if you ever leave it in a hot car the glue may melt since it has a low melting point. Hence the name I guess.
Well, for my ratty old Blazer, any hot glue "damage" to the upholstery can only be an improvement!
gsk11740 is offline  
  Reply With Quote
Old 03-13-2007, 06:38 PM   #10
firemanbill
Community Moderator
 
firemanbill's Avatar
 
Join Date: Sep 2005
Location: Yorktown, Virginia USA
Posts: 18,860
View firemanbill's Gallery67
Thanked 718 Times in 706 Posts
Club: Newport News Park R/C Club
Awards Showcase

125mph Speed Demon  100mph Speed Demon  2kW  4kW 
iTrader: (35)
Friends: (63)
Default

LOL... it's not the blazer I'd be worried about!

2012 SEFF Night Bowling Champion!
firemanbill is offline  
  Reply With Quote
Old 03-13-2007, 06:41 PM   #11
gsk11740
I'm outta here!
 
Join Date: Oct 2006
Posts: 1,195
Thanked 2 Times in 2 Posts
iTrader: (1)
Friends: (0)
Default

Originally Posted by firemanbill View Post
LOL... it's not the blazer I'd be worried about!
Good point!
gsk11740 is offline  
  Reply With Quote
Old 03-13-2007, 08:57 PM   #12
JoeBruce
Member
 
Join Date: Dec 2006
Location: Columbia, MD
Posts: 293
Thanked 0 Times in 0 Posts
iTrader: (0)
Friends: (0)
Default

I can definitely attest to the need for "low temp". I didn't know what kind of cheapo glue gun I bought years ago, but when I tried it on foam I found out it was "high temp". I was able to use it for a little experimental model I didn't really intend to fly, but the glue and tip of the gun both melted the foam as soon as it touched it. Time to buy a low temp gun...

I'll throw out the only other advice I heard on hot glue for airplanes: use it sparingly, not so much because it is heavier than other glues, but because it is easy to overdo it and use more than is necessary.

Joe - AMA # 875529
JoeBruce is offline  
  Reply With Quote
Old 03-13-2007, 09:01 PM   #13
Balil
foam murderer :D
 
Balil's Avatar
 
Join Date: Feb 2007
Location: texas
Posts: 916
Thanked 20 Times in 20 Posts
iTrader: (0)
Friends: (2)
Default

5 min epoxy i found works the best on all joints that need high strength. i keep some in my field kit, and i have even been known to use it for minor repairs at the field.

what goes up, must come down! *looks around* sometimes they come down harder than we intend
Balil is offline  
  Reply With Quote
Old 03-13-2007, 10:57 PM   #14
Son of Paleface
Ozzie Express Wiggy Pilot
 
Son of Paleface's Avatar
 
Join Date: Aug 2005
Location: Yankalilla Australia
Posts: 1,754
Thanked 17 Times in 17 Posts
Awards Showcase

Globetrotter Pilot 
iTrader: (0)
Friends: (8)
Default

some kikers will eat foam get foam safe ones ....gorilla glue used sparingly , damp one side hold together with velcro straps or tape is the best , put some strong tape over the glue joint to help contain the glue expands

We must have had a BIG earthquake...the ground rose up and HIT my plane , Honest

Ozzie Express wiggy pilot
Son of Paleface is offline  
  Reply With Quote
Old 03-13-2007, 11:17 PM   #15
hamothare
New Member
 
Join Date: Aug 2005
Posts: 2
Thanked 0 Times in 0 Posts
iTrader: (0)
Friends: (0)
Default

Go ahead and use oderless CA, it works great. You must use kicker. Using lot of the other glues will take you forever to build. I have built over a hundred foamies for myself and other people with great results by using oderless CA with no proplems. Remember you must use kicker.
hamothare is offline  
  Reply With Quote
Old 03-14-2007, 12:18 AM   #16
markind
Member
 
Join Date: Dec 2006
Posts: 250
Thanked 0 Times in 0 Posts
iTrader: (0)
Friends: (0)
Default

Another problem with Foam Safe CA is that when it hits the kicker, it cures and the chemical reaction releases HEAT!! Enough heat to melt foam!!

I just found this out - fortunately I was only spot-tacking two halves of a canopy together. The tacks held well enough so I could apply epoxy and I reinforced with some fiberglass. Great stuff - high shear strength and light.
markind is offline  
  Reply With Quote
Old 03-14-2007, 01:45 AM   #17
mandoblast
"Thuhwack!"
 
mandoblast's Avatar
 
Join Date: Dec 2006
Location: SE PA
Posts: 9
Thanked 0 Times in 0 Posts
Send a message via AIM to mandoblast
iTrader: (0)
Friends: (0)
Default poly glue and foam

nothing else like it. Epoxy doesn't even stick as well and can be pretty brittle. (adding some micro balloons to the mix seems to help that a lot)
for poly with foam, wet both sides well, apply some glue and rub them together or if you can't do that, smear it arount with a stick. let it cure up really tacky and remove excess along the way. stick 'em together. they might not even need taping/clamping.

That's gonna leave a mark!
mandoblast is offline  
  Reply With Quote
Old 03-14-2007, 02:01 AM   #18
peterkron
Member
 
peterkron's Avatar
 
Join Date: Oct 2006
Location: Lafayette, CA
Posts: 269
View peterkron's Gallery6
Thanked 0 Times in 0 Posts
Send a message via AIM to peterkron
iTrader: (0)
Friends: (0)
Default

Originally Posted by markind View Post
Another problem with Foam Safe CA is that when it hits the kicker, it cures and the chemical reaction releases HEAT!! Enough heat to melt foam!!

I just found this out - fortunately I was only spot-tacking two halves of a canopy together. The tacks held well enough so I could apply epoxy and I reinforced with some fiberglass. Great stuff - high shear strength and light.
yes. the first time i used foam safe ca with accelerator i burned my fingers and it hurts! try not to get that stuff on your fingers
peterkron is offline  
  Reply With Quote
Old 03-14-2007, 04:26 AM   #19
DBacon
Member
 
DBacon's Avatar
 
Join Date: Jun 2006
Location: Shelby Twp, MI USA
Posts: 704
Thanked 127 Times in 113 Posts
Club: www.flyinwolverines.com
iTrader: (0)
Friends: (1)
Default

I have become deathly allergic to the CA kicker, so I use a fine mist of water! It takes 5 mins or so to "firm up" but it is a lot better than the week or two I take to get over the fumes. And it doubles in recuperation time each time I try it.
Gorilla glue mixed with water works much better than just Gorilla glue, setting time is 10 times faster, and it foams up a lot less while setting up.
You gotta really whip it with a popsicle stick in a little plastic cup to get it to mix, but it is worth it.
Wish I could recall who told me this, but it was on this forum for building a MHO or a Gemini.
DBacon is offline  
  Reply With Quote
Old 03-14-2007, 04:39 AM   #20
bowtie hi
Member
 
Join Date: Feb 2007
Posts: 601
Thanked 0 Times in 0 Posts
iTrader: (0)
Friends: (0)
Default

Post # 2 is the way to go. Get a small pump bottle put some baking soda & water in it shake and you have a kicker that don't fume you up and don't melt foam.
WORKS GREAT

Ken

BTW The good point with Gorilla Glue IS the fact it foams up and is lite.
bowtie hi is offline  
  Reply With Quote
Old 03-14-2007, 04:46 AM   #21
DBacon
Member
 
DBacon's Avatar
 
Join Date: Jun 2006
Location: Shelby Twp, MI USA
Posts: 704
Thanked 127 Times in 113 Posts
Club: www.flyinwolverines.com
iTrader: (0)
Friends: (1)
Default

I will add baking soda next time, sounds good. Is it stable enough to sit around and still work weeks later?
And GG is lite. I haven't tried Sumo glue, but heard good things, it is supposed to be similar to GG, but foams less.
Too much foaming from GG may make leakers in pontoons and such.
DBacon is offline  
  Reply With Quote
Old 03-14-2007, 05:30 AM   #22
bowtie hi
Member
 
Join Date: Feb 2007
Posts: 601
Thanked 0 Times in 0 Posts
iTrader: (0)
Friends: (0)
Default

Yep just shake it up and its fine. GG 101 Masking tape over seam you GG and poke holes in it to let excess out leaves smooth surface
bowtie hi is offline  
  Reply With Quote
Old 03-14-2007, 11:34 AM   #23
Slowjohn
You can bury me after I'm done flying
 
Slowjohn's Avatar
 
Join Date: Jan 2006
Location: Mid Coastal TX.
Posts: 2,084
Thanked 133 Times in 130 Posts
Club: Just Some Friends
Awards Showcase

1kW  Globetrotter Pilot 
iTrader: (20)
Friends: (28)
Default

How much baking soda should be used to say 2 ozs. of water? Along this line of Q&A, has anyone tried using regular CA and the baking soda kicker on foam yet? I'm wondering if it will still damage the foam/Depron?
Thanks,
SJ
Slowjohn is offline  
  Reply With Quote
Old 03-14-2007, 02:12 PM   #24
bowtie hi
Member
 
Join Date: Feb 2007
Posts: 601
Thanked 0 Times in 0 Posts
iTrader: (0)
Friends: (0)
Default

I don't put so much in that its to stiff to pump and I use it on everything
bowtie hi is offline  
  Reply With Quote
Old 03-14-2007, 02:41 PM   #25
Slowjohn
You can bury me after I'm done flying
 
Slowjohn's Avatar
 
Join Date: Jan 2006
Location: Mid Coastal TX.
Posts: 2,084
Thanked 133 Times in 130 Posts
Club: Just Some Friends
Awards Showcase

1kW  Globetrotter Pilot 
iTrader: (20)
Friends: (28)
Default

Originally Posted by bowtie hi View Post
I don't put so much in that its to stiff to pump and I use it on everything
Thanks bowtie hi,
The "foam safe CA" is so high in price I think. It's also a 140 mile round trip to the nearest LHS so I just order most everything I need. I think I'll give it a try on a foam trainer I'm about to build for the daughter who wants to try flying one herself. She's done okay on the simulator so I'll build her a simple trainer and see.

Thanks again,
SJ
Slowjohn is offline  
  Reply With Quote
Reply

  WattFlyer RC Electric Flight Forums - Discuss radio control eflight > Electric R/C Airplanes > Foamies

« Previous Thread | Next Thread »

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Foam safe paint? Angler-Hi Foamies 38 02-24-2008 08:10 PM
wanted: foam safe ca. d&mrc General RC items For Sale and WTB 1 11-07-2007 06:22 AM
Foam safe painting. yossarian Foamies 60 07-29-2007 12:35 PM
Foam Safe CA Hinges HAL9000 General Electric Discussions 13 11-05-2006 10:43 PM
Neon foam safe spray paint? Old Fart Scratch and Kit Built Aircraft 7 04-12-2006 11:37 PM


All times are GMT +1. The time now is 01:44 PM.


Powered by: vBulletin
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Copyright 2005 WattfFlyer.com
RCU Eflight HQ

Charities we support Select: Yorkie Rescue  ::  Crohn's & Colitis Foundation



Page generated in 0.28404 seconds with 69 queries