Wattflyer RC Network: RC Universe :: RCU Magazine :: RCU Forums :: RCU Classifieds :: RCU User Reviews :: RCU YouTube
Home Who's Online Calendar Today's Posts RealTime Post Spy Mark Forums Read
Go Back   WattFlyer RC Electric Flight Forums - Discuss radio control eflight > Members List
Register Members List Wattflyer Extras Articles Search Today's Posts Mark Forums Read Social Groups

thepiper92's Profile Picture

thepiper92 thepiper92 is offline

Warbird Fanatic

Visitor Messages

Showing Visitor Messages 1 to 10 of 12
  1. thepiper92
    04-19-2014 08:53 PM
    When you get into more complex builds you'll find you end up doing anything that just works, including different material and things that aren't even on plans
  2. time bandit
    04-19-2014 08:38 PM
    time bandit
    Thanks for the help. I was leaning that way but wanted to be sure before I put the glue to it. Never hurts to ask!!
  3. thepiper92
    04-19-2014 08:25 PM
    I looked at your build, match up the halves with the stab. That little spacing in the middle is the dowel place. Dab some glue on the halves, put in dowel and you can use the stab itself to line everything up.
  4. thepiper92
    04-19-2014 08:21 PM

    That's the build, may not help a lot
  5. thepiper92
    04-19-2014 08:04 PM
    A slot going lengthwise down each half? That's not a bad thing, more surface area for glue. Just have to make sure you sand rounded or a v'ed center hinge, but typical on elevators the area is skinny so it ends up rounded.
  6. time bandit
    04-19-2014 06:46 PM
    time bandit
    Where do I find your P51 build at?
  7. time bandit
    04-19-2014 06:33 PM
    time bandit
    There is a slot already cut into the two elevator halves for the dowel. The instructions say to attach the elevators with a piece of 3/16th inch dowel. I just read it on the online fuse manual and it's the same as the one in my kit. I will check out your P51 build also. Thanks.
  8. thepiper92
    04-19-2014 05:38 PM
    My p51 build may be of some help
  9. thepiper92
    04-19-2014 05:32 PM
    I have not built the EVA, but it sounds the same as the P51. Lay the elevator halves on plans, and glue dowel across halves, so that the dowel is in between the elevator and the horizontal stab end. The dowel is the pivoting area. Do not notch the areas so the dowel sits in the elevator, just glue on surface, unless you plane to sand the edge of the elevator round to match the roundness of the dowel. This is, however, what I did on my P47, but on the P51 the dowel made the round area for pivoting
  10. time bandit
    04-19-2014 04:46 PM
    time bandit
    Hey there I have a question for you. Have you built the EVA sport from Mountain Models? If so How did you glue the 3/16 dowel piece to the elevators? I'm not sure If I lay the elevators flat and glue the round stock in or if I'm supposed to center the elevators on the round stock. Thanks for your time.

About Me

  • About thepiper92
    Winnipeg, Canada
    Rc Planes, Rc Cars, Music (Bagpipes, Saxophone), History,
    Cashier, Student
    Favorite Pet(s)


Total Posts
Visitor Messages
General Information
  • Last Activity: 06-17-2015 09:38 PM
  • Join Date: 11-21-2013
  • Referrals: 0


Showing Friends 1 to 6 of 6

Future expansion tab


My Media


Member Profile Recent Ratings
Feedback Score:
Positive Feedback:
Members who left positive:
Members who left negative:
Total positive feedback: 0
View all feedbacks for thepiper92
6 Months
12 Months
Positive Positive 0 0 0
Neutral Neutral 0 0 0
Negative Negative 0 0 0

All times are GMT +1. The time now is 06:07 AM.

Powered by: vBulletin
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.
Copyright 2005 WattfFlyer.com
RCU Eflight HQ

Charities we support Select: Yorkie Rescue  ::  Crohn's & Colitis Foundation

Page generated in 0.08294 seconds with 33 queries