Search: Posts Made By: GeneR
Showing results 1 to 16 of 16
Search took 0.00 seconds.
10-08-2008, 05:51 PM
Replies: 4
Views: 3,725
Posted By GeneR

Sold on ebay! Thanks everyone! Gene

Sold on ebay!
Thanks everyone!
Gene
09-13-2008, 04:24 AM
Replies: 4
Views: 3,725
Posted By GeneR

Hi, Listed on Ebay: ...

Hi,
Listed on Ebay:
...
09-08-2008, 12:14 AM
Replies: 4
Views: 3,725
Posted By GeneR

Sorry, I cannot go that low. Thanks anyway, ...

Sorry, I cannot go that low.
Thanks anyway,
Gene
09-06-2008, 02:34 PM
Replies: 4
Views: 3,725
Posted By GeneR

Parkzone 1800 Mah 3 Cell LiPo For Corsair or Trojan

I purchased the Parkzone Corsair earlier this week and I already have a number of LiPo packs and chargers so I am selling the included 1800mah 3 cell lipo pack. This is also the standard pack for the...
Forum: ParkFlyers
01-19-2007, 11:50 AM
Replies: 15
Views: 4,013
Posted By GeneR

Removing the jumper sets the cut off for a 3 cell...

Removing the jumper sets the cut off for a 3 cell lipo not a 2 cell. The cut off with the jumper removed was 8.7 volts.

Gene
Forum: ParkFlyers
01-18-2007, 05:07 AM
Replies: 15
Views: 4,013
Posted By GeneR

Oh, I almost forgot that my stock NIMH was an 8.4...

Oh, I almost forgot that my stock NIMH was an 8.4 volt pack, so I am comparing the 2 cell to that .
Gene
Forum: ParkFlyers
01-18-2007, 05:04 AM
Replies: 15
Views: 4,013
Posted By GeneR

First, I changed the connectors to...

First, I changed the connectors to Sermos/Anderson. I put my Astro Watt meter in line to check out what was going on with the power system. I found the cut off of the esc as programmed was...
Forum: ParkFlyers
01-18-2007, 03:51 AM
Replies: 15
Views: 4,013
Posted By GeneR

Yes, The decal set is also a separate part....

Yes,

The decal set is also a separate part. I took all the decals off mine and painted it.

I have been flying it on a 2 cell lipo too!

Gene
01-02-2007, 02:57 AM
Replies: 10
Views: 2,164
Posted By GeneR

I have seen several of your glitching posts. I...

I have seen several of your glitching posts. I have helped quite a number of folks with their CP and CPP's. Here are the sources of glitches I have found.

1. Crystal(s) slightly off frequency....
Forum: 3D Flying
12-14-2005, 04:27 AM
Replies: 26
Views: 6,000
Posted By GeneR

Cyclops, As I say, this is only important on a...

Cyclops,
As I say, this is only important on a heli or 3D plane. I have several 3D foamys where I try to get every mm of throw, even to the point of making an arm extension. For most apps not need...
Forum: 3D Flying
12-14-2005, 03:22 AM
Replies: 26
Views: 6,000
Posted By GeneR

Problem is that if the arm is not centered, you...

Problem is that if the arm is not centered, you will not have equal throws. Since the arm rotates around a shaft, if it is not centered there will be ever so slight differences in throw. This is...
Forum: 3D Flying
12-13-2005, 11:41 PM
Replies: 26
Views: 6,000
Posted By GeneR

Hi, This will not work, at least on my...

Hi,

This will not work, at least on my HS-55 servos. There is a key on the output shaft of the pot which ensures the output gear/shaft is always in the same spot. Removing a gear, then moving...
12-13-2005, 12:52 PM
Replies: 29
Views: 5,868
Posted By GeneR

The XRB is quite a bit more $, from what I...

The XRB is quite a bit more $, from what I understand.

Everything is a compromise, and all RC helis have weak points. Some have broken the flybar mount on the CX. I have 40 flights and so far...
12-03-2005, 02:52 PM
Replies: 29
Views: 5,868
Posted By GeneR

I purchased the CX primarily to learn to nose in...

I purchased the CX primarily to learn to nose in hover. I have a couple of friends who are very experienced heli pilots and they used the XRB (the original coaxial heli model) to learn nose in.
...
12-03-2005, 02:56 AM
Replies: 27
Views: 3,859
Posted By GeneR

I have had mine for a couple of months and flown...

I have had mine for a couple of months and flown it at least every other night. The main shaft is very soft so that whenever you hit anything it bends. I keep 2. I also found it pretty easy to...
12-03-2005, 02:27 AM
Replies: 29
Views: 5,868
Posted By GeneR

I have both the Blade CP and the CX. The CX is...

I have both the Blade CP and the CX. The CX is very stable and probably the easiest way to break into micro electric helicopters. OTOH, the inherent stability makes the CX limited. Great for...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.05949 seconds with 7 queries