Search: Posts Made By: killioughtta
Showing results 1 to 9 of 9
Search took 0.00 seconds.
Forum: ParkFlyers
05-21-2010, 05:48 PM
Replies: 14
Views: 17,366
Posted By killioughtta

The mains are on the slot for the floats so I...

The mains are on the slot for the floats so I can't move them forward without a lot of modifying. I'm not up for that right now. lol
Forum: ParkFlyers
04-03-2010, 08:22 AM
Replies: 14
Views: 17,366
Posted By killioughtta

Hey, it does... a little. Take pictures, man! And...

Hey, it does... a little. Take pictures, man! And post them here. Let me know how it turns out.
Forum: ParkFlyers
03-21-2010, 07:54 PM
Replies: 14
Views: 17,366
Posted By killioughtta

UPDATES are up! Pics and video... :D

UPDATES are up! Pics and video... :D
Forum: ParkFlyers
03-16-2010, 05:50 AM
Replies: 14
Views: 17,366
Posted By killioughtta

So, I'm 90% done with the mod. I replaced the...

So, I'm 90% done with the mod. I replaced the nose gear with the DuBro steerable nose gear and put in a wire-type pushrod that I was going to connect to the rudder servo but I changed my mind since...
Forum: ParkFlyers
03-16-2010, 05:42 AM
Replies: 14
Views: 17,366
Posted By killioughtta

The back gear is actually the back wires for the...

The back gear is actually the back wires for the floats. They are inserted into the stock slot for the floats. This is a new feature in the SC LP fuselage which I bought when building this Cub from...
Forum: ParkFlyers
03-08-2010, 10:56 PM
Replies: 14
Views: 17,366
Posted By killioughtta

I took the SC to the park to see how this gear...

I took the SC to the park to see how this gear holds up. The front wheel is not big enough to ROG off short grass. I hand launched it and checked its behavior (AOA, Trim, etc.) since I had not flown...
Forum: ParkFlyers
03-08-2010, 10:45 PM
Replies: 14
Views: 17,366
Posted By killioughtta

info My Cub is running a TP BM2409-18T Blushless motor...

My Cub is running a TP BM2409-18T Blushless motor with a 9x6 prop.
Forum: ParkFlyers
03-08-2010, 08:42 PM
Replies: 14
Views: 17,366
Posted By killioughtta

The front gear is just a wire glued inside a CF...

The front gear is just a wire glued inside a CF tube held in place by pressure and a bit of glue (so I can remove it later) in the foam. I reinforced it a bit with a plastic washer for rough...
Forum: ParkFlyers
03-08-2010, 07:44 PM
Replies: 14
Views: 17,366
Posted By killioughtta

HZ Super Cub Tricycle Landing Gear

So, I was a little sick of flying from the lake and decided to take the floats off. As I was doing that, I noticed I could use the rear struts for the floats to make a trike gear setup! So I did!
...
Showing results 1 to 9 of 9


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.06227 seconds with 7 queries