Search: Posts Made By: Jools
Showing results 1 to 19 of 19
Search took 0.00 seconds.
Replies: 7
Views: 1,115
Posted By Jools

No it wasn't a gift. I've always been a Futaba...

No it wasn't a gift. I've always been a Futaba man, but I bought this on a whim as I've always rather coveted the JR high-end models. Yes perhaps it was a rash purchase, but it was brand new, been in...
08-14-2019, 01:25 AM
Replies: 11
Views: 3,150
Posted By Jools

I stand corrected. I've used many motors over the...

I stand corrected. I've used many motors over the years but haven't encountered such differences in quoted motor sizes for the same output.
08-14-2019, 12:51 AM
Replies: 11
Views: 3,150
Posted By Jools

I think there could be quite a difference in...

I think there could be quite a difference in those motors, the motor diameter and lengths are very different. Check the motor specs, particularly the max amps figure. You'll probably find that the...
Forum: Power Systems
06-23-2019, 01:29 AM
Replies: 6
Views: 6,773
Posted By Jools

I think the REAL problem is lack of wing area....

I think the REAL problem is lack of wing area. The wing loading must be enormous. It'll have a speed range of very fast and *loody fast!

The other problem may be that big all-moving elevator in...
Forum: Foamies
06-06-2019, 12:02 AM
Replies: 98
Views: 7,208
Posted By Jools

Well, I know where the wing is going to break if...

Well, I know where the wing is going to break if / when it does.
(Plenty of aerodynamic elements we could discuss, but this is just a tip on the structure).
The wing will be dead rigid ending right...
Replies: 1
Views: 570
Posted By Jools

C'mon Radio programming Gurus... this is a...

C'mon Radio programming Gurus... this is a challenge! Find me a mix that'll give me elevator trim.
Forum: Foamies
05-22-2019, 05:30 AM
Replies: 98
Views: 7,208
Posted By Jools

Now, mate, for your next design, use a better...

Now, mate, for your next design, use a better airfoil. That one in your pic is a very high-cambered very thick airfoil, which might be okay on very light wind days, but it won't have the wide speed...
05-22-2019, 05:18 AM
Replies: 5
Views: 1,035
Posted By Jools

Personally I'd be pleased that the wings 'pop...

Personally I'd be pleased that the wings 'pop out' on a hard landing... possibly saves the wings more damage.
05-13-2019, 02:23 AM
Replies: 5
Views: 297
Posted By Jools

The GofG position must be calculated from the...

The GofG position must be calculated from the wing AREA. E.g. 28% of the AREA should be AHEAD of the CofG point, and 72% of the area should be BEHIND the CofG. I'll use 28% as a very realistic...
Replies: 1
Views: 570
Posted By Jools

JR x9*03 Programming advice please

I've been tricking a nice new JRX9503 (very similar to the more common 9303) mode 2 into thinking it's a Mode 1. With success, though not been an easy road.

Everything now works for Mode 1 apart...
Replies: 7
Views: 1,115
Posted By Jools

I'm getting there! I now have all main...

I'm getting there!
I now have all main functions ok for mode 1.
I've got elevator trim now (which was the hitch earlier), by programming in elevator and flap, -but don't have/need flaps. But I get...
Replies: 7
Views: 1,115
Posted By Jools

I've got into the Service menu at last. I've...

I've got into the Service menu at last.
I've changed my mode 2 radio to mode 1 after loads of researching on the internet. My radio is a 9503 and is US model because it has manual throttle trim....
Replies: 7
Views: 1,115
Posted By Jools

Well. I Finally got into the 'SERVICE' MENU, but...

Well. I Finally got into the 'SERVICE' MENU, but it takes me about 9 (yes Nine) alternating flips of the Ail Rate switch and thumbwheel click. Instructions I had read earlier said about 5. So no...
Replies: 7
Views: 1,115
Posted By Jools

Have I been transported back into 1919?...

Have I been transported back into 1919? Bluddy'ell! ;-)
Replies: 7
Views: 1,115
Posted By Jools

Can anyone help with this? Surely I'm not the...

Can anyone help with this? Surely I'm not the only one with this problem?!
Replies: 7
Views: 1,115
Posted By Jools

JR X9503 Get into Service access menu HELP needed

I'm having no luck getting into the Service Menu to change stick mode on my JR X9503 2.4. I've been following instructions on another forum, but it's for a 9303 radio. Maybe it's a different routine?...
03-24-2019, 01:35 AM
Replies: 2
Views: 1,167
Posted By Jools

Correct me if I'm mistaken, but I thought LiFe...

Correct me if I'm mistaken, but I thought LiFe were lower voltage than LiPo, 9.9v nominal, as opposed to 11.1v, and had much lower discharge rates than LiPo.
03-22-2019, 02:37 PM
Replies: 5
Views: 15,167
Posted By Jools

My fuselage moulds.

My fuselage moulds.
03-22-2019, 02:19 PM
Replies: 5,460
Views: 875,706
Posted By Jools

My view...

Looking forward to being involved here. Hopefully I'm now getting back into flying after some years 'off'.

I started out many years ago slope soaring, and more recently (like most slopers I'd...
Showing results 1 to 19 of 19


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.05404 seconds with 7 queries