Search: Posts Made By: solentlife
Showing results 1 to 11 of 11
Search took 0.00 seconds.
10-27-2015, 08:11 AM
Replies: 106
Views: 21,104
Posted By solentlife

Hi G ... surely before maiden when you were...

Hi G ... surely before maiden when you were setting up controls, a 1/2 inch difference in elevators should have been obvious ?
I always elevate model to eye-line and the view along length of model...
10-25-2015, 10:56 PM
Replies: 106
Views: 21,104
Posted By solentlife

The elevators ... two servos on separate...

The elevators ... two servos on separate channels ?

... I had similar problem on a couple of models of mine that I changed to separate servos ... with single - I had unequal movement and still...
10-25-2015, 08:36 AM
Replies: 106
Views: 21,104
Posted By solentlife

The VERY BEST OF LUCK ..... Go get'm !! ...

The VERY BEST OF LUCK .....

Go get'm !!

Nigel
10-19-2015, 06:35 PM
Replies: 106
Views: 21,104
Posted By solentlife

Given the amount of surface area of the 22 .... I...

Given the amount of surface area of the 22 .... I would forget Flaps and go for Spoilers so I get a better rate of descent while still controlling speed.

Many models are actually better at...
10-15-2015, 07:59 AM
Replies: 106
Views: 21,104
Posted By solentlife

One of the earlier posts - you mention heavy tail...

One of the earlier posts - you mention heavy tail parts .... something that could be done when converting - is to carefully remove the film / covering and then cut lightening holes in any solid...
10-08-2015, 03:20 PM
Replies: 106
Views: 21,104
Posted By solentlife

There are 12x7 and various other you could use if...

There are 12x7 and various other you could use if you need more thrust / power.

Nigel
10-08-2015, 03:19 PM
Replies: 106
Views: 21,104
Posted By solentlife

There are plenty of third party suppliers of...

There are plenty of third party suppliers of shafts and in different lengths / C clip placement / etc.

RCtimer.com is a good place to look ...

You can customise a motor with a shaft from them...
10-07-2015, 07:04 AM
Replies: 106
Views: 21,104
Posted By solentlife

Heat is the usual way to 'break' Loctite. Either...

Heat is the usual way to 'break' Loctite. Either a soldering iron on the bolt head or as I have ... a mini Butane torch.

Just a comment .... when I have a hole or failed bulkhead as you now have...
10-05-2015, 08:45 PM
Replies: 106
Views: 21,104
Posted By solentlife

No sweat .... I too am not a great follower of...

No sweat .... I too am not a great follower of watts / lb .... I prefer to look at thrust vs weight.

I'm interested to see the results of this conversion.

Nigel
10-05-2015, 04:41 PM
Replies: 106
Views: 21,104
Posted By solentlife

No disrespect intended but we all know that full...

No disrespect intended but we all know that full size are working on much lower ratios.

0.8:1 I fine for sunday sport flying .... but soon leads to wanting more oooomph !

You only have to...
10-05-2015, 04:18 PM
Replies: 106
Views: 21,104
Posted By solentlife

My questions are : Tractor or Pusher ? ...

My questions are :

Tractor or Pusher ?

AUW once battery / Motor / Rx etc. fitted ?

You show a weight of ~84oz bare frame weight ... and a thrust of 84oz from motor combo.

I usually do not...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.06341 seconds with 7 queries