Search: Posts Made By: danman_83
Showing results 1 to 17 of 17
Search took 0.00 seconds.
Replies: 4
Views: 3,287
Posted By danman_83

They were used...hi tec hbs65..i haven't tried...

They were used...hi tec hbs65..i haven't tried changing channels with it yet, i'll give it a shot and let you know what happens...the problem is that it only does it occasionally
Replies: 4
Views: 3,287
Posted By danman_83

I mean the elevator servo I believe...the...

I mean the elevator servo I believe...the rearmost servo controlling the swashplate
Replies: 4
Views: 3,287
Posted By danman_83

Question Servo flutter/malfunction

I just got a an Align T-Rex and bought a new DX6i tx/rx to go with it. I have an older used lipo and fired it up and got it flying, when I got a servo flutter, my rear servo started fluttering on its...
Replies: 6
Views: 2,833
Posted By danman_83

i'm a big fan of diy repairs, especially since I...

i'm a big fan of diy repairs, especially since I will be having to pay for them all ;) i don't think death by 2 year old is covered under warranty. I don't want to wait for shipping, pay for...
08-01-2009, 07:10 PM
Replies: 7
Views: 2,158
Posted By danman_83

Thanks for all the inputs, I'd already replaced...

Thanks for all the inputs, I'd already replaced the feathering shaft, but I found out later after going to my lhs that the guy who had the bird before me didn't have near enough shims in the head,...
Replies: 6
Views: 2,833
Posted By danman_83

Sweet, i'll look there next time i'm in town....

Sweet, i'll look there next time i'm in town. Appreciate the advice all!
Replies: 6
Views: 2,833
Posted By danman_83

Broken Switch DX6i

My 2 year old got a hold of my DX6i and dropped it, breaking the Rudder switch. I took it apart and couldn't fix it, but I have been looking all over the internet for a part for the darned thing....
06-17-2009, 01:53 AM
Replies: 5
Views: 1,209
Posted By danman_83

thanks heliG, I had to go to work. I followed...

thanks heliG, I had to go to work. I followed those instructions on my CP+ having zero soldering experience, just borrowed a nice adjustable iron from a friend and went to town...I bought the stock...
06-16-2009, 04:14 PM
Replies: 5
Views: 1,209
Posted By danman_83

It sounds to me like you either got a bad 3 in 1,...

It sounds to me like you either got a bad 3 in 1, or had another problem that blew the 3in1 right away. I had the same problem on my cp+ with the tail rotor, same situation though and it ended up...
06-16-2009, 03:26 AM
Replies: 7
Views: 2,158
Posted By danman_83

Head SHAKE

I had an extremly timid "crash" the other day with my CP+, it came down from about 1 foot off the ground and barely touched a blade to the cement. It broke the blade which I new would happen so I...
Replies: 4
Views: 1,960
Posted By danman_83

I live in the sticks, I'm about the only person...

I live in the sticks, I'm about the only person in a 20 mile radius that will be flying most days....so i'm not too worried about interference, I'm mostly looking for price :) The servos are...
Replies: 4
Views: 1,960
Posted By danman_83

Question Looking to buy...what radios and servos are good?

I'm looking at getting a

I have a Futaba 7CAP/CHP Helicopter/Airplane radio that I'd like to part with. It's in great condition and comes with 2 receivers.

Part comes complete with:
- 7...
06-04-2009, 10:13 PM
Replies: 1
Views: 1,316
Posted By danman_83

Also, I was just thinking and wondering and not...

Also, I was just thinking and wondering and not knowing, if it would be safe to switch the throttle and rotor leads from the rx to the esc to help diagnose if the tx is bad or if the rx is...
06-04-2009, 10:08 PM
Replies: 1
Views: 1,316
Posted By danman_83

Exclamation Blade CP+ Rotor Issue

Hey I have a blade cp + that I recently landed a little too hard with. The tail motor went out, and I replaced it, only to find that it now won't work at all. Now I had the problem before that I...
05-13-2009, 04:41 AM
Replies: 5
Views: 1,792
Posted By danman_83

Thanks for all the input! I ordered a few mosfets...

Thanks for all the input! I ordered a few mosfets off of digikey and tried my hand at soldering for the first time today. Total Success!!! After 3 hours of painstaking learning on that stupid...
Forum: Power Systems
05-08-2009, 11:49 PM
Replies: 0
Views: 578
Posted By danman_83

Build Review 3-in-1 Problem? Blade CP+

I'm including a pic of my 3-in-1 in with this post. My tail motor burnt up and then when I replaced it, it stayed on regardless of input from controller, I read the post about replacing the mosfet...
05-08-2009, 08:05 AM
Replies: 5
Views: 1,792
Posted By danman_83

Help CP+ tail motor problem

I recently aquired a cp+ heli used, and pretty much out of the box the tail motor burned up without any crashes or strikes of any kind. I replaced the motor and got it all wired in, but now when I...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.04357 seconds with 7 queries