Search: Posts Made By: VENOMOUS
Showing results 1 to 24 of 24
Search took 0.00 seconds.
05-15-2006, 05:57 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

@TravinB, The radio system is not...

@TravinB,

The radio system is not compatible with any others out there but you can still tune the 3D to react slower.
Relocate the swashplate links to the servos from the middle hole on the...
04-24-2006, 06:53 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

@katoomtom The blade pitch range is off a...

@katoomtom

The blade pitch range is off a little bit and the servos are pulling the swash assem apart. Disconnect your motor and mark the plugs so you dont switch them later. Go through the pitch...
04-20-2006, 06:46 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

@ KRS It sounds like you would really...

@ KRS

It sounds like you would really benefit from reading the threads on Lipo use and safety. This cell type is no different in terms of danger or safety compared to the conventional cell types,...
04-20-2006, 02:19 AM
Replies: 428
Views: 89,705
Posted By VENOMOUS

There it is, the 50's work. Please make sure that...

There it is, the 50's work. Please make sure that you use all the same kind of servo's or you might have mixing issues (I would expect you could) because CCPM is very sensitive to this issue.
...
04-19-2006, 09:22 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Check to see if the head block has come loose,...

Check to see if the head block has come loose, the green aluminum part. Slide it to the top of the main shaft's flat for the set screw and tighten it there. Then check your pitch range as described...
04-19-2006, 09:17 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

No worries :) Chris

No worries :)

Chris
04-18-2006, 12:48 AM
Replies: 428
Views: 89,705
Posted By VENOMOUS

@ Viking I dont want to argue with you but...

@ Viking

I dont want to argue with you but I dont work in the CS Dept. so I dont see their emails, I was talking about PM's here and that I would be alerted to them through my inbox in Outlook at...
04-12-2006, 07:11 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Oh by the way there is no need for second tail...

Oh by the way there is no need for second tail motor on the 3D. There isnt any lack of tail perfomance thats for sure.

Chris
04-12-2006, 07:09 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

@ Viking I was looking at the dates on the...

@ Viking

I was looking at the dates on the previous page and I see I was talking with you about your tail motor issue a little bit. In other words I was aware the problem was getting attention....
03-29-2006, 06:42 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Hey sorry I didnt get to you sooner. I'm glad you...

Hey sorry I didnt get to you sooner. I'm glad you figured it out.
You should post some shots of the UFO! The night blades should be arriving in the next week or so. That would really get the light...
03-21-2006, 06:27 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Hey thats great you got up and flying again. You...

Hey thats great you got up and flying again. You might try slowing the response rate of you model down if you have not already. This done by moving the servo links in one hole from the outside...
03-13-2006, 07:06 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Hey Viking, Welcome, and congrats on the...

Hey Viking,

Welcome, and congrats on the successfull flying, keep it up!

Chris
03-03-2006, 05:51 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

We have an office in Australia, look in your...

We have an office in Australia, look in your manual we are in Botany.

Chris
03-03-2006, 05:50 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Hey guys just checking in, anything major going...

Hey guys just checking in, anything major going on?

Ive done tests on different heli's by clamping them down to a stand to get performance measurements and all of them will vibrate a bit, some...
02-06-2006, 06:43 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Not me, thats Paul S. We took that photo at...

Not me, thats Paul S. We took that photo at C.A.M.S. club field where we fly all of the time.

Chris
02-06-2006, 06:05 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

While the blades are a little stiffer than the...

While the blades are a little stiffer than the stock ones thats not where your flex comes from entirely. The whole airframe will flex during a hard landing or crash. The tail boom is too stiff to...
01-31-2006, 05:46 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Thats true, its just a spacer. The ones that...

Thats true, its just a spacer. The ones that count are the the spur gear, the one above the upper bearing for the mast, and the head block. All of those need to be tight and threadlocked.

Chris
01-31-2006, 12:48 AM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Another forum answer to the same question about...

Another forum answer to the same question about tail wagging on the 3D
"@blues
Try adjusting the PZT nob to reduce or eliminate the wag and pay attention to the direction you adjust it. This will...
01-31-2006, 12:46 AM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Hey do both! Try the fix and get the new parts as...

Hey do both! Try the fix and get the new parts as back ups!:rolleyes:

Chris
01-26-2006, 02:36 AM
Replies: 428
Views: 89,705
Posted By VENOMOUS

@Blues Please preflight it again and check...

@Blues

Please preflight it again and check your blades are 0'ed out as prescribed above. Also unlock your radio and set the pitch nobs to 12o'clock position for starters. I find they dont...
01-25-2006, 01:44 AM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Here are a few updates from another thread on...

Here are a few updates from another thread on RCgroups

We are providing an update to this issue.

Initial blade pitch set up

The blades should be at 0deg. pitch in Normal Mode when the...
01-24-2006, 01:15 AM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Hi Zap, PM me with your info and I'll check the...

Hi Zap,
PM me with your info and I'll check the shop for your model.

Ok, I'll be back with some info....

Chris
01-23-2006, 10:19 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Cool thanks, this thread looks pretty active too,...

Cool thanks, this thread looks pretty active too, I see some familiar names here.
Would it be a problem to cut and paste the updates and tips from another thread here? Their pretty extensive and I...
01-23-2006, 07:23 PM
Replies: 428
Views: 89,705
Posted By VENOMOUS

Hey guys just checking in. My name is Chris...

Hey guys just checking in.
My name is Chris Nicastro and I'm the Direstor of R&D for Venom Group International. I have been active on other threads in an effort to support your needs outside of our...
Showing results 1 to 24 of 24


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.05777 seconds with 7 queries