Best Way to Straighten out you bent prop shaft?? - WattFlyer RC Electric Flight Forums - Discuss radio control eflight

RCU RSS Feed RC Unviverse General Electric Discussion forum rss feed

Best Way to Straighten out you bent prop shaft??

Old 08-13-2006, 12:20 AM
  #1  
RSS Feed
Member
Thread Starter
 
Join Date: Aug 2006
Posts: 301
Default Best Way to Straighten out you bent prop shaft??

Hey all, I bent my prop shaft on my outrunner and cant get the thing dead straight, whats the best way u guys use?? I was thinking of a threaded tube...

More...
RSS Feed is offline  
Old 08-17-2006, 01:48 PM
  #2  
Solid Hit
Just call me ... Bill
 
Solid Hit's Avatar
 
Join Date: Mar 2006
Location: Upstate of SC
Posts: 1,186
Default

If it is bent about an inch from the motor, simply cut it off and fit it with either a prop adapter or a prop saver.

Otherwise, just replace it. I don't believe you can ever get it perfectly balanced and will eventually end up causing problems due to vibration.
Solid Hit is offline  
Old 04-21-2011, 07:00 PM
  #3  
Flywhat2
One hitch AE1 -- USN
 
Flywhat2's Avatar
 
Join Date: Dec 2010
Location: New York State
Posts: 82
Default Bent Motor shaft

Trust me, replace it, they are usually pretty cheap and you will prolly never get it straight. Voice of (limited) experience.
Best of luck, Fly
Flywhat2 is offline  
Old 04-21-2011, 07:51 PM
  #4  
flydiver
Super Contributor
 
flydiver's Avatar
 
Join Date: Jan 2007
Location: Seattle, WA
Posts: 2,668
Default

VERY VERY hard to get properly straight again. I have a mongo drill press and a special device called a dial indicator that is perfect for the job and I can seldom do better than 0.003 and often no better than 0.006. You can't see that with the naked eye or the 'glass top roll' but it shows on the motor.

For the most part and by far the best results > replace. While out spin the bearings with a pencil point. Often (most often) a crash hard enough to bend a shaft dings the bearings too. They do not like impact side loading. They should be absolutely smooth.
flydiver is offline  
Old 04-21-2011, 08:15 PM
  #5  
JetPlaneFlyer
Super Contributor
 
JetPlaneFlyer's Avatar
 
Join Date: Mar 2009
Location: Aberdeen, Scotland
Posts: 6,120
Default

Another vote for 'replace'.. it's best to keep a couple of spares. Even if you could get it dead straight (which is all but impossible) it would be weakened.

Steve
JetPlaneFlyer is offline  
Old 12-30-2011, 07:06 PM
  #6  
coritco566
New Member
 
Join Date: Aug 2009
Location: Alanta Georgia
Posts: 4
Default

Replace it been there...
coritco566 is offline  
Old 12-31-2011, 02:44 AM
  #7  
kyleservicetech
Super Contributor
 
kyleservicetech's Avatar
 
Join Date: Apr 2008
Location: Wisconsin, USA
Posts: 8,952
Default

Originally Posted by coritco566 View Post
Replace it been there...
This is an old thread, but agreed, replace the shaft.

Some of the shafts are hard steel, bending them back can result in those shafts snapping off. Other issues, its very possible the shaft is bent both outside the motor and inside the motor. And, in between is the motor ball bearings on that shaft. Often those ball bearing get "Ball Dented" on the bearing races. The motor will run, but those bearings are going to fail much sooner than expected.

I've also tried to straighten motor shafts, by mounting the motor in my 12 inch Lathe, and dial indicating the motor shaft. It's a lot of work, but found that Hacker motors has those shafts for my A40-10L motor for five bucks. Not worth messing with bent shafts.
kyleservicetech is offline  
Old 03-15-2012, 07:04 PM
  #8  
Paulo69
Member
 
Paulo69's Avatar
 
Join Date: Mar 2012
Location: Cape Town - South Africa
Posts: 74
Default

Get some drill-bit blanks from an engineering supplier and there you go ...
Paulo69 is offline  
Old 03-15-2012, 08:16 PM
  #9  
Voltron
Member
 
Voltron's Avatar
 
Join Date: May 2008
Location: Finger Lakes Region, NY
Posts: 377
Default

Im going to chime in here and agree with everyone who says to replace the shaft. If you don't get it perfect, you will shake your plane apart. I saw a bent prop shaft rip the whole nose off from a foamy a few years ago. Heads Up RC has replacement shafts that will fit a bunch of different motors.
Voltron is offline  
Old 03-15-2012, 09:10 PM
  #10  
Paulo69
Member
 
Paulo69's Avatar
 
Join Date: Mar 2012
Location: Cape Town - South Africa
Posts: 74
Default

I totally agree ... replace, replace, replace, but IF on the odd occasion, you can't get your hands on a replacement shaft, and don't want to toss the motor, a drill bit blank works like a charm HSS and straight as an arrow
Paulo69 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
cbusse1
Brushless Motor Construction
21
08-10-2007 05:48 PM
Lip84
Power Systems
10
02-14-2007 10:54 PM
electricfly
Beginners - Helis
0
01-05-2007 11:06 AM
Bunky
Beginners
3
09-12-2005 02:32 AM
donjiskra
Power Systems
10
09-07-2005 07:59 AM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Quick Reply: Best Way to Straighten out you bent prop shaft??


Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.10570 seconds with 13 queries