Beginners New to e-power flying? Get the low down in here from experienced e-power RC pilots!

Somethin' Extra electric conversion

Old 08-16-2020, 10:35 PM
  #1  
prowler53
New Member
Thread Starter
 
Join Date: Jul 2020
Posts: 14
Default Somethin' Extra electric conversion

Well here she is after 17 years of hanging in a bedroom and never flown. I removed all the covering and gave it a fresh look, Made some Mods for the conversion. Added a hatch at the front for battery and a hatch under the front fuse for ESC. Dubro landing gear and 2 1/2" wheels for prop clearance. I have a 13x8 on her right now but probably room for a 14" If I decide to go larger. E-flite Power 46 and 60 amp ESC. 4S 4500 mah Lipo. Extended The Rudder and covered in Monokote. I used Oracal 651 vinyl for the graphics. She still comes in a little tail heavy with everything moved forward, so I'm thinking about a larger battery & prop spinner. 5.4 Lbs right now without adding more weight, so I think I'm going to end up around 6 Lbs when ready to fly. A little heavier than I wanted but I think it should be ok.

Attached Thumbnails Click image for larger version

Name:	SSE.jpg
Views:	16
Size:	5.22 MB
ID:	188194  
prowler53 is offline  
Old 08-17-2020, 03:19 AM
  #2  
Turbojoe
Mountain Models Minion
 
Turbojoe's Avatar
 
Join Date: Aug 2005
Location: Mesa, Arizona
Posts: 1,255
Default

That looks AMAZING! Nice work!

Joe
Turbojoe is offline  
Old 08-17-2020, 10:54 AM
  #3  
ron_van_sommeren
homo ludens modelisticus
 
ron_van_sommeren's Avatar
 
Join Date: Jul 2005
Location: near Nijmegen, Nederland
Posts: 1,209
Default

Originally Posted by prowler53 View Post
... I have a 13x8 on her right now but probably room for a 14" If I decide to go larger. ...
Both current and power drawn are proportional to diameter⁴, here they would increase by factor (14/13)⁴=1.35, 35%more.
(Ignoring higher voltage losses in battery, wiring, controller, motor due the higher current).

What's the current draw with the 13"diameter prop?

14" is better but you may need to reduce pitch should current get too high. Current drawn is proportional to pitch (also proportional to #blades, voltage≤ and Kv≥).

Last edited by ron_van_sommeren; 08-18-2020 at 05:30 PM.
ron_van_sommeren is offline  
Old 08-17-2020, 11:05 AM
  #4  
ron_van_sommeren
homo ludens modelisticus
 
ron_van_sommeren's Avatar
 
Join Date: Jul 2005
Location: near Nijmegen, Nederland
Posts: 1,209
Default

It is a good practice to have some headroom built in.
About derating motors, controllers, batteries, electronics in general:
ron_van_sommeren is offline  
Old 08-17-2020, 09:25 PM
  #5  
prowler53
New Member
Thread Starter
 
Join Date: Jul 2020
Posts: 14
Default

Originally Posted by Turbojoe View Post
That looks AMAZING! Nice work!

Joe
Thanks Joe
prowler53 is offline  
Old 08-17-2020, 09:27 PM
  #6  
prowler53
New Member
Thread Starter
 
Join Date: Jul 2020
Posts: 14
Default

Originally Posted by ron_van_sommeren View Post
Both current and power drawn are proportional to diameter⁴, here they would increase by factor (14/13)⁴=1.35, 35%more.
(Ignoring higher voltage losses in battery, wiring, controller, motor due the higher current).

What's the current draw with the 13"diameter prop?

14" is better but you may need to reduce pitch should current get too high. Current and power drawn are proportional to pitch (also proportional to voltage≤ and Kv≥).
I'm not sure of the draw yet....I have a Watt meter ordered and should be here this week.
prowler53 is offline  
Old 08-23-2020, 03:04 PM
  #7  
prowler53
New Member
Thread Starter
 
Join Date: Jul 2020
Posts: 14
Default

Watt meter arrived but now I'm waiting on my transmitter that is being repaired or replaced because of the faulty scroll wheel switch. I was bored yesterday and took an hour drive to the closest r/c hobby shop. Ended up coming home with an E-flite Night Timber x BNF.
I heard good things about this plane, and thought it would be good to get some practice with before flying the Somethin' extra. Now I just need my transmitter to get flying.
prowler53 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
AEAJR
Beginners
165
06-28-2017 04:22 PM
AEAJR
Beginners
28
02-16-2016 12:19 AM
Doc Austin
3D Flying
5
01-05-2013 03:19 AM
kyleservicetech
Sport Planes (Formerly I/C & Gas Conversion)
12
04-06-2011 10:46 PM
sgillmore
Power Systems
7
04-01-2011 03:37 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Quick Reply: Somethin' Extra electric conversion


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.09808 seconds with 11 queries