Batteries and Chargers Forsale/WTB list your batteries and Chargers for sale here

For Sale Power supplies 12v or 24v plug and play

Old 03-12-2012, 05:26 AM
  #1  
jrplane
New Member
Thread Starter
 
Join Date: Aug 2005
Posts: 12
Default Power supplies 12v or 24v plug and play

Power supplies 12v or 24v plug and play

12volt 47 amp 564 watt,
24volt 47 amp 1130 watt.
I am using two in series for 24v on my lab 8, they are very stable, rock solid,
They are set up ready to go with 4mm outlets and power cords.

Heres a close up of the bussiness end of the power supply.
You can see the 24v model is double wrapped, comes with jumper to allow 24V. as you can see you can use 2-12v and 1-24v at the same time. 2-12v top row , 24v bottom row, or remove the jumper and you have 4-12v outlets. With the jumper in place you also can use the out two far out side connections for two 24V outputs. These power supplies are rated at 47 amps. I have personally abused my test setup, just to see where the fail point is. I have had my Lab 8 with 6-5000 3S @ full 40 amp charge and a cellpro 10 with 2-5S running wide open. I'm still using this power supply with no problem. Just because I did this for testing purposes,,,,,,,,,
I DO NOT RECOMMEND GOING OVER RATED OUTPUT!!!

Singles are 12v and white $55 shipped

Doubles are 12v and 24v and black $110 shipped

These are 100% ready to use. Plug and play.

I am a noobie here but have lots of 100% good trader rating on RCG, RCU, and ebay
Attached Thumbnails Click image for larger version

Name:	IMG_2643.jpg
Views:	726
Size:	123.6 KB
ID:	158102   Click image for larger version

Name:	IMG_2642.jpg
Views:	542
Size:	94.8 KB
ID:	158103   Click image for larger version

Name:	IMG_2641.jpg
Views:	318
Size:	116.5 KB
ID:	158104  
jrplane is offline  
Old 03-27-2012, 09:48 PM
  #2  
chriscap16
Member
 
Join Date: Mar 2011
Posts: 29
Default

How are you handling the grounding issue? Are you essentially not handling it and insulating with the cardboard, or are you making an internal modification of some sort
chriscap16 is offline  
Old 03-27-2012, 10:37 PM
  #3  
JetPlaneFlyer
Super Contributor
 
JetPlaneFlyer's Avatar
 
Join Date: Mar 2009
Location: Aberdeen, Scotland
Posts: 6,121
Default

Yeah, grounding is key. When i made up my power supply using the same DPS-600PB units I insulated the relevant PCB mounting stud and cut a couple of wire jumpers so that the second unit in the series pair could be floated at +12V while still having it's case grounded to earth.

The 'hope for the best' solution is just to disconnect the earth on the second unit but that way if you get a fault then you could be electrocuted, which isnt very nice at all

Not an issue if you are just using a single 12v unit of course.

jrplane,
I like the way you have used female bullets to hook up to the hot swap connector, much neater than soldering in wires.

Steve
JetPlaneFlyer is offline  
Old 04-06-2012, 09:44 PM
  #4  
jrplane
New Member
Thread Starter
 
Join Date: Aug 2005
Posts: 12
Default

Hi guys,

Yes these have the DC ground floated, There is no cardboard, however there is a this peice of foam between them, strapping tape to hold them secure. Then finally wrapped into one nice package. These things are solid! Not like some on the net.

Jeff

Please email me at [email protected] I am not get notices from the web site.

Last edited by jrplane; 04-07-2012 at 05:35 AM.
jrplane is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
wolfewinde
ParkFlyers
40
08-13-2011 02:22 AM
1987tc
Airplanes - Electric For Sale & WTB
4
05-06-2011 04:25 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Quick Reply: For Sale Power supplies 12v or 24v plug and play


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.06773 seconds with 17 queries