FMA Direct Discuss FMA Direct products or ask your support questions.

FMA CPII + Blade 450 3D

Old 12-19-2011, 11:15 PM
  #1  
ukpete
New Member
Thread Starter
 
Join Date: Dec 2011
Posts: 1
Default FMA CPII + Blade 450 3D

I have a CPII system which I'm planning on installing to my stock Blade 450 3D.

I had a look at the connections and channels on my receiver tonight and I'm a little confused as to what plugs where when looking at the servo connections.

Have you got any advice on how to connect it up to this helicopter?

I'm only using 3 servos for stabilisation I think - 2 aileron and 1 cyclic - is that correct?

I assume then, that I only use the 3 SVO* connections. It also doesn't seem to matter which order the SVO connections get made, just that I must use SVO1->RCV1 and SVO2->RCV2,SVO3->RCV3, is that correct?

I have a DX6i - does anyone know if you can use a channel on that to switch CPII off and on, and if so, how?

Sorry to appear dumb, but I'm just trying to get my head round connecting it up.

Pete


ukpete is offline  
Old 12-20-2011, 08:26 PM
  #2  
Howard Matos
Production Supervisor
 
Howard Matos's Avatar
 
Join Date: Sep 2008
Location: Frederick, MD
Posts: 77
Default

Originally Posted by ukpete View Post
I have a CPII system which I'm planning on installing to my stock Blade 450 3D.

I had a look at the connections and channels on my receiver tonight and I'm a little confused as to what plugs where when looking at the servo connections.

Have you got any advice on how to connect it up to this helicopter?

I'm only using 3 servos for stabilisation I think - 2 aileron and 1 cyclic - is that correct?

I assume then, that I only use the 3 SVO* connections. It also doesn't seem to matter which order the SVO connections get made, just that I must use SVO1->RCV1 and SVO2->RCV2,SVO3->RCV3, is that correct?

I have a DX6i - does anyone know if you can use a channel on that to switch CPII off and on, and if so, how?

Sorry to appear dumb, but I'm just trying to get my head round connecting it up.

Pete

Hi,

Here is some helpful information that should answer your questions:

What servos do I connect to the avionics computer for flight stabilization?
You need to connect the pitch (elevator) and roll (aileron) servos for flight stabilization. For 3D airplane flight modes, you will also need to connect yaw (rudder). For CCPM helicopters, you will also connect collective servo.

For aircraft:

Aileron (1 or 2 channel input)
Elevator (1 or 2 channel input)
Rudder (for 3D mode - must have available input)

Old time aircraft

Rudder
Elevator

For Helicopter:

non CCPM
Cyclic roll (aileron)
Cyclic pitch (elevator)

CCPM
Cyclic roll (aileron)
Cyclic pitch (elevator)
Collective

What is the proper direction to connect servo leads to the avionics computer?
All servo leads, including the CP II sensors and IR router, connect with the black (ground) lead towards the CP II label.

Do the channels on my receiver match up to the inputs on the avionics computer?
No. The servo inputs on the avionics computer are totally independent from the channels on your receiver. Just make sure you connect the servos mentioned in the FAQ "What servos to I connect to the avionics computer for flight stabilization?" above. The order that the servos plug into the avionics computer does not matter. The computer learns the control settings during setup. Just make sure the input numbers match the output numbers; e.g., if you use RCV1 for Elevator, plug the elevator servo into SVO1, etc. Never connect throttle through the CPII avionic computer.

Do I have to connect my gyro control to the avionics computer?
No. The gyro control (1 wire servo lead normally connected to channel 5) is only connected to the avionics computer when you want to free up a channel.

Does it matter which way the vertical sensor is mounted?
Yes! The vertical sensor must be mounted with the arrow pointing towards the sky.





If you have any other questions, please contact me direct at [email protected]. Thanks!
Howard Matos is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
raitheslacker
Radio Equipment For Sale & WTB
1
09-17-2012 09:13 PM
kenchiroalpha
E-Flite Helicopters
3
05-16-2012 06:24 AM
Old Blade Man
Helicopters- Electric For Sale & WTB
0
11-10-2011 08:33 PM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Quick Reply: FMA CPII + Blade 450 3D


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.

Page generated in 0.06948 seconds with 14 queries